YBM single-drum combined anchor windlass
Chain diameter ranging: φ17-φ50, pull force: 8-50 KN
Victory Machinery equipment is born of innovation and backed by years of experience. All our anchor windlasses, ancillary deck gear, stern-handling products and accessories provide a level of quality, functionality, durability and style that is unparalleled in the industry.
To make the proper selection in anchor winch equipment, it is important to give careful consideration to the style and size of boat, the anticipated anchoring conditions, and the weight and type of ground tackle. For assistance in determining what anchoring solution is right for you, refer to the Which Winch section above, or contact your nearest Victory Machinery representative.
Vertical and Horizontal Winches
Vertical systems have several advantages: They take up less space on deck and are easier to maintain. They are less expensive than equivalent horizontal models. Chain alignment for smooth chain retrieval, while important, is not as critical as horizontal windlass alignment. With vertical systems more chain is in contact with the chain wheel thus avoiding the possibility of chain jump. Line-pull on the warping drum can be in any direction, as opposed to fore and aft only on horizontal models.
Horizontal models have the advantage of being better suited to applications where there is limited below deck space / accessibility, extreme deck thickness (over 200mm – 8″), or where two anchors must be handled from one winch.
Winch Selection Guide
There are a number of important criteria to be considered in selecting the correct anchor winch. These include the vessel size, displacement, wind age, anchor size and rode selection. Practicalities such as locker space and depth of fall for the rode also play a part in deciding which windlass is ideal for you. Victory Machinery Marine’s range of windlasses and capstans is extensive, with models to suit boats and marine industry. This section aims to simplify the selection process by taking you step by step through all the criteria that needs to be considered when choosing a windlass or capstan.
VERTICAL OR HORIZONTAL CONFIGURATION ?
The two basic types of windlasses are differentiated by the drive shaft orientation. Deck thickness and under deck space are the two main considerations when deciding which of the two types to fit. Vertical windlasses make up the majority of anchor winch sales. They are characterized by situating the capstan and/or gypsy above deck and the motor and gearbox below deck. Vertical windlasses provide a 180° wrap of the anchor rode around the chain wheel giving optimal chain control, minimizing slippage and jumping. Horizontal windlasses are mounted completely above deck with gypsy and capstan located to either side. They provide a 90° wrap of the rode around the chain wheel.
HOW MUCH SPACE DO I NEED IN MY CHAIN LOCKER?
Deck thickness and locker space play an important role in deciding whether to install a vertical or horizontal windlass. Estimating or measuring the depth of fall of the rode into the anchor locker may dictate which type of windlass is most suitable for your vessel. Calculating the depth of fall differs for horizontal chain only windlasses and for vertical rope or rope/chain windlasses.
Rope and/or chain, particularly chain selection, is extremely important. Deciding on the right anchor winch for your boat depends on the size, not only of the boat, but also the ground tackle. Victory Machinery anchor winches and capstans are designed to take chain only, rope only or a combination of both. Automatic rope/chain systems are now commonly used on boats up to 20 metres (65 feet). Consequently, Victory Machinery’s Freedom, HRC, RC10 and Liberty Series automatic rope/chain systems have become increasingly popular, as they offer the added benefit of less weight in the bow with the ability to carry an increased amount of rode. Chain only systems remain popular on heavier displacement sail and motor yachts. There are two main types of anchor chain. Short link chain is most commonly used on small and medium sized boats while stud link chain is generally used on much larger vessels such as Super yachts. The latter is characterized by a stud (bar) joining the two sides of the link preventing them from deforming when overloaded. High test or calibrated short link chain should always be used. Long or regular link chain should not be used with anchor windlasses. There are a wide variety of both metric (mm) and imperial (inches) chain sizes available and these will have bearing on your final windlass decision. It is important that the right size and right grade of chain is used to ensure a correct fit of the links to the gypsy. If the chain is not matched to the chain wheel problems may occur, such as the chain jumping off the gypsy or the chain jamming as it will not feed smoothly through the chain pipe. As chain to chain wheel compatibility is so important, Victory Machinery Marine supplies chain wheels to fit just about every known chain available on today’s international market.
DC, AC OR HYDRAULIC?
The wattage of a DC electric motor is not the important factor. Rather it is the efficiency of the whole winch, including the gearbox and motor, which counts. With the increasing popularity of powerful and compact on-board generators, AC powered winches are becoming a practical consideration for bigger boats. Hydraulic systems provide another power source well worth considering as they have the advantage of constant speed under all load conditions and can be run almost constantly while coupled with safe guards such as pressure relief valves. Modern hydraulic systems offer an integrated, low maintenance and efficient, centrally managed, power pack.
WHAT PULL CAPABILITY WILL I NEED?
The only meaningful way to rate anchor winch performance is by looking at what it will lift and at what speed. The two things to consider are (a) the maximum pull capability and (b) the working load of the winch. Maximum pull (sometimes referred to as stall load) is the maximum short term or instantaneous pull of the winch. Working load is generally rated at about one third of the maximum pull and is usually considered to be the load that the winch is pulling once the anchor is off the bottom. To determine your required maximum pull capability, complete the calculation below.
SAFETY AND SECURITY TIPS
Circuit breaker/isolators are used in the installation of any DC electric windlass to provide protection to motor and cables should the windlass be overloaded. Accessories such as chain stoppers or chain snubbers are highly recommended for safe anchoring, the avoidance of unintentional self- launching of the anchor and for the prevention of damage to your anchor winch. You should never anchor off your winch or use your winch to draw your boat to the anchor spot. The anchor winch is designed to pull up a dead weight and should not be subjected to the strain of your boat riding at anchor. If you think the winch you are considering may be too small, then go to the next size up. Better to have excess lifting capacity than not enough! Victory Machinery Marine and their agents or distributors offer free and helpful advice should you have any questions.
|Working load (KN)||Over load pulling force (KN)||Holding load